Cory
The pics I see of the red boat has a motor mount a grade level up from mine.  My aluminum rails are attached directly to the hull. There is a Delrin (I think) strip that runs on the inside of the channel, bottom to top. I took some pics and will send them out on Monday if I can. 
Ric 
Dadventure

Sent from my iPhone

> On Nov 14, 2020, at 11:38 AM, Lee Kuhn <lvjkuhn at gmail.com> wrote:
> 
> ?The minute I get off the waiting list at your marina I'll pull the trigger
> on getting a recycled one from Stan.
> 
>> On Sat, Nov 14, 2020, 11:31 AM Cary Tolbert <retiredtoby at gmail.com> wrote:
>> 
>> Thanks Lee. Your boat looks like it was upgraded in its  life. That system
>> is much newer and a better thought out system than the one on my 86.
>> Rob's 90 something has something similar for his 9.9 hp with all electrical
>> controls.
>> Any luck on tracking down your Rhodes 22 to be?
>> Cary
>> 
>>> On Sat, Nov 14, 2020 at 11:18 AM Lee Kuhn <lvjkuhn at gmail.com> wrote:
>>> 
>>> Gary,
>>> 
>>> Don't know if any of the attached of my former 1986 AT EASE will help.
>>> Might need to enlarge.  Seems like a variety of stops might work.  Good
>>> luck!
>>> 
>>> Lee
>>> No Boat Yet
>>> Claytor Lake, VA
>>> 
>>> On Sat, Nov 14, 2020 at 10:16 AM Cary Tolbert <retiredtoby at gmail.com>
>>> wrote:
>>> 
>>>> I am asking for help with photos for an 86 Rhodes.  My boat was
>>>> apparently hit
>>>> in the marina and I have a damaged motor mount. I was able to salvage
>>> most
>>>> of the damaged parts and replicate them from existing patterns of the
>> old
>>>> parts.
>>>> However, the LOWER STOPS were missing. So at this point I have no idea
>>> what
>>>> I need to do to replicate these parts. Photos will be very helpful.
>>>> Measurement would also be greatly appreciated. I am guessing any boat
>>> from
>>>> an 82 to an 89 may have a very similar set up.  Ric I am glad you can
>> now
>>>> send pictures with your computer. You mentioned that we have the same
>> set
>>>> up. What type of material did Stan use for the stops?  Stan said, he no
>>>> longer makes this type of mount and cannot furnish parts. So I must
>> rely
>>> on
>>>> your help and my modest skills to be able to sail next season.
>>>> It must have been a lot of force on the collision as I found three
>> 1/4
>>>> inch stainless steel bolts bent to 90 degrees and one bolt was sheared
>>> into
>>>> two pieces.
>>>> 
>>>> Thanks for your help,
>>>> Cary Tolbert
>>>> S/V Whisper "86
>>>> Radford, VA
>>>> 
>>> -------------- next part --------------
>>> A non-text attachment was scrubbed...
>>> Name: Motor Lift Side.jpg
>>> Type: image/jpeg
>>> Size: 1770484 bytes
>>> Desc: not available
>>> URL: <
>>> 
>> http://rhodes22.org/pipermail/rhodes22-list/attachments/20201114/c7f75d52/attachment.jpg
>>>> 
>>> -------------- next part --------------
>>> A non-text attachment was scrubbed...
>>> Name: Motor Lift Top.jpg
>>> Type: image/jpeg
>>> Size: 1804873 bytes
>>> Desc: not available
>>> URL: <
>>> 
>> http://rhodes22.org/pipermail/rhodes22-list/attachments/20201114/c7f75d52/attachment-0001.jpg
>>>> 
>>> -------------- next part --------------
>>> A non-text attachment was scrubbed...
>>> Name: Motor Lift Side Top.jpg
>>> Type: image/jpeg
>>> Size: 1845462 bytes
>>> Desc: not available
>>> URL: <
>>> 
>> http://rhodes22.org/pipermail/rhodes22-list/attachments/20201114/c7f75d52/attachment-0002.jpg
>>>> 
>>> 
>>